|
|
| Stud precision attachments are primarily used
on roots and implants for retaining removable partial dentures or overdentures. All stud
attachments MUST be parallel to each other to provide ease of insertion and removal and
reduce wear potential. Do not engage labial soft tissue undercuts with the denture base
flange, as this will alter the path of insertion and cause excessive wear and servicing
requirements. Stud attachments are low in profile to reduce leverage upon the retaining
abutments, are easy for patient hygiene maintenance, allow physiologic independent
movement of abutments, and are easy to independantly service.
|
Preci Clix OD
Direct Placement or cast coping
Spherical overdenture attachment system that allows the user to
replace both the male (threaded sphere) and female. Choose from threaded, bondable, or castable 2.25mm spheres.
The females
engage the undercuts of the sphere to allow for superior retention, patient-pleasing audible click, and less attachment wear. |
|
|
Clix 1261
threaded |
|
Clix 1291
direct/threaded
|
Clix 1293
direct/one piece
|
- 3.50mm tall
- 3.50mm Ø tooth surface
- 4.00mm Ø housing
|
- 4.30mm tall
- 4.00mm Ø tooth surface
- 4.00mm Ø housing
|
- 5.50mm tall
- 4.00mm Ø tooth surface
- 4.00mm Ø housing
|
- 4.15mm in tall
- 4.00mm Ø tooth surface
- 4.00mm Ø housing
|
- 4.00mm tall
- 4.00mm Ø tooth surface
- 4.00mm Ø housing
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| |
|
|
Locator Root
Locator Components
Locator Direct Placement Instructons
Locator Cast Coping Instructions
Direct Placement or cast coping
The Self-Aligning Pivoting feature of the LOCATOR attachment allows a
patient to easily seat their overdenture without the need for accurate
alignment of the attachment components.
- Long Lasting--good for 110,000 insertion cycles!
- Self-Aligning--patient can bit prosthesis to place!
- Patented Dual Retention
- Unique Pivoting Denture Cap
- Choice of Retention--5, 4, 3, 2, 1.5, 1 and 0 lbs
- Extra-Radicular Design
- Money-Back Guarantee
Compare the Locator to the ERA® Requires:
- 3.00mm tall
- 4.00mm Ø tooth surface
- 5.50mm Ø housing
|
|
| |
|
|
Ceka
Attachments
Ceka Revax Inverted Axial (M2 and M3)
Inverted Axial Female Bonding Technique
Technique: Male retained in the prosthesis
The Ceka Revax and the Axial Ceka Revax
stud attachments both feature a direct cast to capability. The
new Ceka Revax (M2) is the smallest fully adjustable and serviceable
stud attachment system. This adjustable spring pin attachment
may be utilized as a traditional stud (with cast copings), or
inverted as an intraradicular connector for overdentures or
removable partial dentures on roots and implants. It may be
used for a resilient or tissue born prosthesis, or for a combination
abutment and tissue supported prosthesis. The small size allows
for usage when space is at a premium--ideal for ‘close
bite’ situations. Clinical, laboratory, and servicing are
routine procedures that are adaptable to the individual’s
needs and/or techniques.
Ideal for low profile CAD-CAM bars!
Requires:
| |
M2 Inverted Axial |
M3 Inverted Axial |
| |
3.80mm tall |
4.35mm in vertical tall |
| |
4.00mm Ø tooth surface |
4.30mm Ø tooth surface |
| |
3.40mm Ø housing |
4.40mm Ø housing |
Ceka Revax Traditional Axial (M2 and M3)
Axial Base Ring Solder Technique
Axial Base Ring Cast To Technique
Technique: Female retained in the prosthesis
The traditional Ceka Axial has been in
use for over 30 years. As a result, it is one of the most widely
used attachments in the world. It is much like the Ceka Revax
Axial, but for one major difference--the Ceka requires 0.45
mm more vertical clearance. When space is available, select
the traditional M3 Ceka as it is stronger and easier to service.
Requires:
| |
M2 Inverted Axial |
M3 Inverted Axial |
| |
3.60mm tall |
4.00mm tall |
| |
4.00mm Ø tooth surface |
4.30mm Ø tooth surface |
| |
3.40mm Ø housing |
4.20mm Ø housing |
|
Ceka Inverted Axial (M3)
Traditional Ceka Axial (M3)
move mouse over model
|
| |
|
| |
|
| |
|
Preci-Ball
Preci
Ball Castable Male Instructions
The Preci Ball 22 is a
resilient (full rotation) stud attachment. It is a
simple, effective systems, with many options to protect the abutments and
retain both partials and overdentures. The spherical male attachment is
available in a prefabricated orax alloy
for soldering, a burnout plastic pattern for
direct casting, and also a threaded male
for direct casting or soldering. The female is available in a prefabricated alloy
and a threaded female. There is also an optional threaded
replaceable female.
The Preci Ball allows for an
easy path of insertion and removal, adjustable
female, and easy patient hygienic maintenance. All adjustments
are made in the removable prosthesis. These features allow the
dental professional to alter the attachment to fit the patient's
needs, not vice versa.
Require:
- 3.40mm tall , 4.35mm for threaded male
- 3.55mm Ø tooth surface
- 3.50mm Ø housing
|
Preci-Ball 22
|
| |
|
Shiner Magnet
Shiner Magnet Instructions
Magnetic systems provide:
- no path of insertion for patients with limited dexterity
- limited servicing requirements for the operator
- up to 24º of rotation per abutment for non-parallel abutments
- prosthesis may engage undercuts for increased stability
Shiner magnets provide retention in two different sizes:
Requires:
| |
Standard Magnet |
Mini Magnet |
| |
3.40mm tall |
2.40mm tall |
| |
5.50mm Ø housing |
3.90mm Ø housing |
| |
4.00mm Ø tooth surface |
3.60mm Ø tooth surface |
|
 |
| |
|
OSO
Overdenture/Post
OSO Overdenture
Instructions
View
OSO O-Ring Size Chart
Direct Placement or cast coping
The OSO Overdenture system features simple techniques,
low cost, versatility, a pressure relief system for seating,
the ability to be used in combination with splinting bars, processing
jigs that allow dentists to cement the crowns at time of try
in and provide simple repair or replacement of the removable
prosthesis. The OSO is maintenance free...there is nothing to
repair except the O-ring, which may be replaced in minutes. The posts are 5.8mm
in height, and the actual male component is 3.2mm in height.
Requires:
- 3.20mm tall
- 3.00mm Ø tooth surface
- 4.50mm Ø housing
|
a
O-SO OD Attachment
|
| |
|
| |
|
Sphero Flex Post
Sphero Flex Post Direct Placement Instructions
Sphero Flex Post Cast Coping Instructions
Direct Placement or cast coping
The Sphero Flex
Post system is an endodontic post rotating ball attachment that
corrects misalignment in any plane up to 15 degrees. The advantages
of this self paralleling system are the freedom of movement
(resiliency) that protects weak abutments, the biocompatibility
of titanium, easy conventional techniques, and the small size
of the sphere (2.5 mm). Also, no potential debris can enter
the female, eliminating potential insertion problems. The female
may be seated in the prosthesis, or incorporated in to a cast
frame. The posts are available in three lengths-- 6.75 mm, 8.40
mm, and 9.75 mm. The 2 degree precision reamer assures accuracy. This system can also be used with a cast coping.
Requires:
- 3.40mm tall
- 3.55mm Ø tooth surface
- 4.10mm Ø housing
|
a
Sphero Flex Post
|
| |
|
| |
|
|
Concave Sphere
Reconstruction Kit
The titanium Sphero Reconstrution kit is designed to
allow for a rebuilding of worn spheres in the mouth to restore long term
retention and stability for the patient using concave Titanium spheres.
Other uses for this kit include increasing the diameter of a small sphere in
the mouth or retrofitting an O-Ring attachment to a ball attachment.
Requires:
- vertical height increase or decrease is case dependant
- 4.80mm Ø housing
There are 3 different diameter spheres:
|
| |
|
| |
|
| |
|
Locator Retrofit Kit #1747
for Worn ERA Root Attachments
Procedure Manual
LOCATOR RETROFIT – ERA ROOT ATTACHMENT
Package of 2
(Includes LOCATOR® Retrofit, Parallel Post, Weep Hole Alignment Pin)
Please order Locator males separately. 
Requires:
- 0.3mm in additional vertical height of existing ERA
- 5.50mm Ø housing
|
|
| |
|
| |
|
ZAAG
Kits
ZAAG Components
ZAAG Instructions
Direct Placement or cast coping
Zest Anchor Advanced Generation (ZAAG) is
an improvement over the traditional Zest Anchor system while
maintaining Zest concepts: lowering the fulcrum (force application),
the intradicular female (inside root), and the easy replacement
of the male. Advancements allow the male to freely rotate and
move within the housing or denture cap, the wide band on the
male allows for increased retention and reduced wear (less bending
and breakage), the female has a titanium coating for hardness
and a smoother internal surface.
Requires:
| |
Standard ZAAG |
Mini ZAAG |
| |
4.50mm tall* |
3.50mm tall* |
| |
3.80mm Ø housing |
3.30mm Ø housing |
| |
4.00mm Ø tooth surface |
3.50mm Ø tooth surface |
*the short and tough housing may be used instead of the standard housing to reduce vertical height by 1mm
|
ZAAG
a 
| standard cap male |
|
short and tough cap male |
| |
|
|
|
| |
|
| |
|
Zest Anchor
After 25 years of use, Zest Anchors has undergone a
series of improvements to create the all new Zest Anchor Advanced
Generation (ZAAG). Preat has a complete inventory of Zest parts
and accessories for servicing existing prosthesis. We recommend
the Locator Attachment for all
new cases.
Requires:
- 3.50mm tall
- 4.70mm Ø tooth surface
- 3.50mm Ø housing
|
|
|
| |
|
|
